Omega Wiki - User contributions [en]

80-series

2026-03-25T15:44:01Z

70.228.96.105: /* New 80 Series Firmware */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
Data protocol and engine detection now set upon key start during vehicle learn 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 
V1.1 Release 1/5-2026 
*Clean up brake input via data to address programming issues. 
*Add 45 and 60 minute run time. 
*New runtimes do not allow runtime reset. 
*Add N/O and Brake Activated Starter Interrupt. 
*Rearrange Bank 5 feature order. 
*Add option for Brown siren wire to be Start Interrupt. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 
** Hold Trunk while connecting USB connected to Nutek site. 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2026-01-30T18:35:30Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
Data protocol and engine detection now set upon key start during vehicle learn 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 
V1.0 Release 1/5-2026 
*Clean up brake input via data to address programming issues. 
*Add 45 and 60 minute run time. 
*New runtimes do not allow runtime reset. 
*Add N/O and Brake Activated Starter Interrupt. 
*Rearrange Bank 5 feature order. 
*Add option for Brown siren wire to be Start Interrupt. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 
** Hold Trunk while connecting USB connected to Nutek site. 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2026-01-20T19:03:31Z

70.228.96.105: /* New 80 Series Firmware */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 
V1.0 Release 1/5-2026 
*Clean up brake input via data to address programming issues. 
*Add 45 and 60 minute run time. 
*New runtimes do not allow runtime reset. 
*Add N/O and Brake Activated Starter Interrupt. 
*Rearrange Bank 5 feature order. 
*Add option for Brown siren wire to be Start Interrupt. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 
** Hold Trunk while connecting USB connected to Nutek site. 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2026-01-20T19:03:03Z

70.228.96.105: /* New 80 Series Firmware */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 
V1.0 Release 1/5-2026 
Clean up brake input via data to address programming issues. 
Add 45 and 60 minute run time. 
New runtimes do not allow runtime reset. 
Add N/O and Brake Activated Starter Interrupt. 
Rearrange Bank 5 feature order. 
Add option for Brown siren wire to be Start Interrupt. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 
** Hold Trunk while connecting USB connected to Nutek site. 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-11-04T20:15:32Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 
** Hold Trunk while connecting USB connected to Nutek site. 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-11-04T20:15:06Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 
** Hold Trunk while connecting USB and connected to Nutek site. 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-11-04T20:12:46Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold Start for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-09-16T18:55:54Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*Snap together case, no screws 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold "P" for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-09-16T18:30:13Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*To turn On - Hold "P" for ~5 seconds 
*To turn Off - Hold "P" & Start for ~5 seconds 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-09-05T15:07:02Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 
=New 80 Series Firmware=
V1.0 Initial release 8/5-2025 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-07-18T15:27:03Z

70.228.96.105:

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability 

==Good to know stuff/DEV notes==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time

80-series

2025-07-18T15:25:53Z

70.228.96.105: /* Good to know stuff */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Good to know stuff==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-07-14T18:40:08Z

70.228.96.105: /* Good to know stuff */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Good to know stuff==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 
Hood no longer acts as Door for MT mode, all system have dedicated door trigger 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-07-11T19:28:58Z

70.228.96.105: /* Blade control Module (AL-80-B / RS-80-B) */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Good to know stuff==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-07-11T16:38:51Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Good to know stuff==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT. 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
*Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT. 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-07-11T16:36:09Z

70.228.96.105: /* Good to know stuff */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Good to know stuff==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 
Programmable analog LED outputs and antenna LED timing will not be 100% synced. 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-07-11T16:34:53Z

70.228.96.105: /* Quarks */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Good to know stuff==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-07-11T16:34:29Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as analog Wait-to-Start 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process 
New antennas will work as RF kit for RS-80-G0 
70-series remotes and antennas are '''NOT''' compatible with 80-series 
Remotes now transmit upon button release OR after button is held for 2 seconds 
==Quarks==
Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is 

=New 80 Series Feature Programming=
'''New Programmable Feature Menus''' 
Features are now broken into 6 Banks 
*'''1. RS Options''' 
*'''2. Convenience Options''' 
*'''3. Security Options''' 
*'''4. System Behaviors''' 
*'''5. Output Config''' 
*'''6. Input Config''' 
Feature programming now uses prog button and brake to select banks, feature, and options. 
#Enter programming with Ignition On/Off and prog button 5x 
##System will confirm, with 2 chirps 
##Ignition back On '''IF''' brake requires ignition On for operation 
#Use prog button to select desired feature bank 
##System will respond with chirps to correspond to selected bank number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with 1x chirp 
#Use prog button to select desired feature 
##System will respond with chirps to correspond to selected feature number 
##Chirps will repeat after ~2 seconds delay 
#Press brake to confirm selection 
##System will respond with chirps to indicate current option setting of selected feature 
#Use prog button to select desired option within feature 
##System will respond with chirps to correspond to selected option 
#Press brake to confirm selection 
##System will respond with 1x chirp and return to feature selection in current bank 
##Pressing Brake again will go back to the bank selection option 
#Turn Ignition On/Off or wait to exit programming 
 
'''Feature Reset''' - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires 
'''1514 Reset''' - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:55:27Z

70.228.96.105: /* New 80 Series Features */

80-series

2025-06-11T16:48:56Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
----
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:48:37Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
----
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs.
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:47:17Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
----
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs 
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:46:56Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
----
Select inputs/outputs can be configured as status light outputs and override inputs 
*When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
*Resistors may be needed for any LED not designed to operate at 12V
Select inputs can be configured as Arm or Disarm inputs
Select inputs can be configured as N/C inputs for Hoood, Door, or Trunk zones

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:40:12Z

70.228.96.105: /* New 80 Series Features */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
----
Select inputs/Outputs can be configured as status light outputs and override inputs 
*When an alternative Override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:35:19Z

70.228.96.105: /* Non-blade control module (AL-80 / RS-80) */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:33:43Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
*New xASK logo replaces x433 
*Plastic case with metal trim ring 
*Snap together case, no screws 
*CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
*New xASK logo replaces x433 
*CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
*New xASK logo replaces x433 
*USB-C charge port 
*USB-C firmware update capability

80-series

2025-06-11T16:32:02Z

70.228.96.105: /* Blade control Module (AL-80-B / RS-80-B) */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:31:39Z

70.228.96.105: /* Non-blade control module (AL-80 / RS-80) */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:31:30Z

70.228.96.105: /* Blade control Module (AL-80-B / RS-80-B) */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 

===Blade control Module (''AL-80-B / RS-80-B'')===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:30:56Z

70.228.96.105: /* Non-blade control module (AL-80 / RS-80) */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
*Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
**Red/White is now Red/Black 
*Includes single analog sensor port and door triggers in sub harness 
*New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
*New 12-pin harness with 22AWG wires for all inputs and low current outputs 
*New antenna port is not 4-pin iData connector on side of module 
*Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 

===Blade control Module (''AL-80-B / RS-80-B'')===
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:28:16Z

70.228.96.105: /* Non-blade control module (AL-80 / RS-80) */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 
===Blade control Module (''AL-80-B / RS-80-B'')===
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:28:05Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') ===
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 
===Blade control Module (''AL-80-B / RS-80-B'')=== 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:27:40Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
=== Non-blade control module (''AL-80 / RS-80'') === 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 
===Blade control Module (''AL-80-B / RS-80-B'')=== 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:26:33Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
===Non-blade control module (''AL-80 / RS-80'')=== 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 
===Blade control Module (''AL-80-B / RS-80-B'')=== 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:24:50Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
--Non-blade control module (''AL-80 / RS-80'')-- 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 
-Blade control Module (''AL-80-B / RS-80-B'')- 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:24:33Z

70.228.96.105: /* New 80 Series Hardware */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
-Non-blade control module (''AL-80 / RS-80'')- 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
 
-Blade control Module (''AL-80-B / RS-80-B'')- 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 

=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:21:38Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
Non-blade control module (AL-80 / RS-80) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
Blade control Module (AL-80-B / RS-80-B) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
:CR-2032 battery 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
:CR-2032 battery 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:20:13Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
Non-blade control module (AL-80 / RS-80) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
Blade control Module (AL-80-B / RS-80-B) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
'''1514-03''' - Five button 2-way with new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:19:56Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
Non-blade control module (AL-80 / RS-80) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
Blade control Module (AL-80-B / RS-80-B) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
'''1420-03''' - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
'''1514-03''' - Five button 2-way witn new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:19:35Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
Non-blade control module (AL-80 / RS-80) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
Blade control Module (AL-80-B / RS-80-B) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
=New Remotes=
'''119-03''' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
"1420-03" - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
'''1423-03''' - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
""1514-03"" - Five button 2-way witn new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:18:55Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
Non-blade control module (AL-80 / RS-80) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
Blade control Module (AL-80-B / RS-80-B) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
=New Remotes=
''119-03'' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
1420-03 - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
1423-03 - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
1514-03 - Five button 2-way witn new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

80-series

2025-06-11T16:18:42Z

70.228.96.105: /* New Remotes */

=New 80 Series Features=
'''New Programmable Feature Structure''' 
Features are now broken into 6 Banks 
'''1. RS Options''' 
'''2. Convenience Options''' 
'''3. Security Options''' 
'''4. System Behaviors''' 
'''5. Output Config''' 
'''6. Input Config''' 
Programming now uses Prog button and Brake to select banks, feature, and options. 
Enter programming with Ignition On/Off and valet 5x 
:System will confirm, with 2 chirps 
:Ignition back On '''IF''' brake requires ignition On for operation 
Use prog button to select desired feature bank 
:System will respond with chirps to correspond to selected bank number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with 1x chirp 
Use prog button to select desired feature 
:System will respond with chirps to correspond to selected feature number 
:Chirps will repeat after ~2 seconds delay 
Press brake to confirm selection 
:System will respond with chirps to indicate current option setting of selected feature 
Use prog button to select desired option within feature 
:System will respond with chirps to correspond to selected option 
Press brake to confirm selection 
:System will respond with 1x chirp and return to feature selection in current bank 
:Pressing Brake again will go back to the bank selection option 
'''Feature Reset''' - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults. 
 
 

=New 80 Series Hardware=
Non-blade control module (AL-80 / RS-80) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes single analog sensor port and door triggers in sub harness 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series 
Blade control Module (AL-80-B / RS-80-B) 
Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges 
:Red/White is now Red/Black 
Includes two analog sensor ports that are now independent zones(1 - White / 1-Yellow) 
New 4-pin harness w/ (+/-)P/L, Ground, and Siren 
New 12-pin harness with 22AWG wires for all inputs and low current outputs 
New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs 
New antenna port is not 4-pin iData connector on side of module 
Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series 
=New Remotes=
'119-03' - One button 1-way in carryover case from 70-seroes 
:New xASK logo replaces x433 
1420-03 - Four button 1-way with new case design 
:New xASK logo replaces x433 
:Plastic case with metal trim ring 
:Snap together case, no screws 
1423-03 - Four button 1-way in carryover all plastic case from 70-seroes 
:New xASK logo replaces x433 
1514-03 - Five button 2-way witn new case and screen layout 
:New xASK logo replaces x433 
:USB-C charge port 
:USB-C firmware update capability

Linkr-LT

2023-11-03T20:09:58Z

70.228.96.105: /* Linkr-LT2 Alarm Alerts */

=Linkr-LT2 Alarm Alerts=
With last 6 of the serial number the unit can be located in the system and an Initialize command can be sent to clear and reset alert status. 
ShawnC or MikeT might be able to send command from Admin site if unit was activated with Omega App. 
AutoMobility can send command to any device. Send email request to help@mycarcontrols.com to have command sent. 
'''2022 APP UPDATE''' allows end user to select "input alarm detection" on or off. 

=Linkr-LT2 Coverage Map=
Go to T-Mobile site and enter customers zip code. 
[https://www.t-mobile.com/coverage/coverage-map T-Mobile Coverage Map] 
 
'''Excellent signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Good signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Fair signal''' = 3G Fallback on AT&T network. Mostly outside major cities. 
'''Partner''' = 3G Fallback on AT&T network. Mostly in remote locations. 
AT&T fallback has been known to have poor to no operation 

=App secret features=
Change Protocol - Press and hold the protocol icon in the config screen for 5 - 6 seconds. Warning will appear confirming you are going to make a change, choose "OK". 
Changing dealer number -in the dealer number screen tap the Linkr logo 5 - 7 times quickly. 

=ProCom Brand ID using M2M Suite=
Look in the "History" of the device in question. The first account the device is placed in determine the brand. 
100001 = Rockford CDMA (discontinued) 
100002 = AutoMob 
100003 = Visions 
100004 = Kia 
100007 = Voxx CarLink 
100008 = Omega (includes 100006-Linkr & 100009-Tele-Connect)

Linkr-LT

2023-11-03T20:09:39Z

70.228.96.105: /* Linkr-LT2 Alarm Alerts */

=Linkr-LT2 Alarm Alerts=
With last 6 of the serial number the unit can be located in the system and an Initialize command can be sent to clear and reset alert status. 
ShawnC or MikeT might be able to send command from Admin site if unit was activated with Omega App. 
AutoMobility can send command to any device. Send email request to help@mycarcontrols.com to have command sent. 
2022 APP UPDATE allows end user to select "input alarm detection" on or off. 

=Linkr-LT2 Coverage Map=
Go to T-Mobile site and enter customers zip code. 
[https://www.t-mobile.com/coverage/coverage-map T-Mobile Coverage Map] 
 
'''Excellent signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Good signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Fair signal''' = 3G Fallback on AT&T network. Mostly outside major cities. 
'''Partner''' = 3G Fallback on AT&T network. Mostly in remote locations. 
AT&T fallback has been known to have poor to no operation 

=App secret features=
Change Protocol - Press and hold the protocol icon in the config screen for 5 - 6 seconds. Warning will appear confirming you are going to make a change, choose "OK". 
Changing dealer number -in the dealer number screen tap the Linkr logo 5 - 7 times quickly. 

=ProCom Brand ID using M2M Suite=
Look in the "History" of the device in question. The first account the device is placed in determine the brand. 
100001 = Rockford CDMA (discontinued) 
100002 = AutoMob 
100003 = Visions 
100004 = Kia 
100007 = Voxx CarLink 
100008 = Omega (includes 100006-Linkr & 100009-Tele-Connect)

Linkr-LT

2023-11-03T20:08:36Z

70.228.96.105: /* App secret features */

=Linkr-LT2 Alarm Alerts=
With last 6 of the serial number the unit can be located in the system and an Initialize command can be sent to clear and reset alert status. 
ShawnC or MikeT might be able to send command from Admin site if unit was activated with Omega App. 
AutoMobility can send command to any device. Send email request to help@mycarcontrols.com to have command sent. 

=Linkr-LT2 Coverage Map=
Go to T-Mobile site and enter customers zip code. 
[https://www.t-mobile.com/coverage/coverage-map T-Mobile Coverage Map] 
 
'''Excellent signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Good signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Fair signal''' = 3G Fallback on AT&T network. Mostly outside major cities. 
'''Partner''' = 3G Fallback on AT&T network. Mostly in remote locations. 
AT&T fallback has been known to have poor to no operation 

=App secret features=
Change Protocol - Press and hold the protocol icon in the config screen for 5 - 6 seconds. Warning will appear confirming you are going to make a change, choose "OK". 
Changing dealer number -in the dealer number screen tap the Linkr logo 5 - 7 times quickly. 

=ProCom Brand ID using M2M Suite=
Look in the "History" of the device in question. The first account the device is placed in determine the brand. 
100001 = Rockford CDMA (discontinued) 
100002 = AutoMob 
100003 = Visions 
100004 = Kia 
100007 = Voxx CarLink 
100008 = Omega (includes 100006-Linkr & 100009-Tele-Connect)

Linkr-LT

2023-11-03T19:21:52Z

70.228.96.105: /* ProCom Brand ID using M2M Suite */

=Linkr-LT2 Alarm Alerts=
With last 6 of the serial number the unit can be located in the system and an Initialize command can be sent to clear and reset alert status. 
ShawnC or MikeT might be able to send command from Admin site if unit was activated with Omega App. 
AutoMobility can send command to any device. Send email request to help@mycarcontrols.com to have command sent. 

=Linkr-LT2 Coverage Map=
Go to T-Mobile site and enter customers zip code. 
[https://www.t-mobile.com/coverage/coverage-map T-Mobile Coverage Map] 
 
'''Excellent signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Good signal''' = 4G LTE on T-Mobile network. Mostly in major cities. 
'''Fair signal''' = 3G Fallback on AT&T network. Mostly outside major cities. 
'''Partner''' = 3G Fallback on AT&T network. Mostly in remote locations. 
AT&T fallback has been known to have poor to no operation 

=App secret features=
Change Protocol - Press and hold the protocol icon in the config screen for 5 - 6 seconds. Warning will appear confirming you are going to make a change, choose "OK". 
Changing dealer number -

=ProCom Brand ID using M2M Suite=
Look in the "History" of the device in question. The first account the device is placed in determine the brand. 
100001 = Rockford CDMA (discontinued) 
100002 = AutoMob 
100003 = Visions 
100004 = Kia 
100007 = Voxx CarLink 
100008 = Omega (includes 100006-Linkr & 100009-Tele-Connect)

OL-HRN-RS Rules

2023-09-21T17:57:39Z

70.228.96.105: /* T-Harness Compatibility Rules */

=T-Harness Compatibility Rules=
'''OL-HRN-RS-CH4''' - All vehicles covered by OL-RS-CH4 with MT vehicles added. DL-CH4 firmware. 
'''OL-HRN-RS-CH5''' - All vehicles covered by OL-RS-CH5 with MT vehicles added. DL-CH5 firmware. 
'''OL-HRN-RS-CH7''' - All vehicles covered by ADS-THR-CH10 with MT vehicles added then ''exclude'' Dodge Dart, Fiat 500, Jeep Compass & Renegade. DL-CH7, CH8, CH12, RS-CH7, CH8, & CH12. 
'''OL-HRN-RS-FM2''' - All vehicles covered by OL-RS-FO1 with MT vehicles added. DL-FM2 firmware. 
'''OL-HRN-RS-FM3''' - All vehicles covered by OL-RS-FO1 with MT vehicles added. DL-FM3 firmware. 
'''OL-HRN-RS-FM8''' - All vehicles covered by ADS-THR-FM8, NO MT vehicles. DL-FM8 & RS-FM8 firmware. 
'''OL-HRN-RS-GM8''' - All vehicles covered by ADS-THR-GM13 with MT vehicles added. DL-GM8, GM12, & RS-GM8 firmware. 
'''OL-HRN-RS-GM10''' - All vehicles covered by ADS-THR-GM10 with MT vehicles added. DL-GM10 firmware. 
'''OL-HRN-RS-GM12''' - All vehicles covered by ADS-THR-GM7 or GM12. DL-GM7 and GM12 firmware. 
'''OL-HRN-RS-HA3''' - All 
'''OL-HRN-RS-HA6''' - All 
'''OL-HRN-RS-HA7''' - All 
'''OL-HRN-RS-HK''' - All vehicles covered by ADS-THR-HK5 with MT vehicles added. 
'''OL-HRN-RS-MA3''' - All vehicles covered by ADS-THR-MA3 with MT vehicles added. DL-MA3 firmware. 
'''OL-HRN-RS-NI3''' - All 
'''OL-HRN-RS-NI4''' - All 
'''OL-HRN-RS-NI5''' - All 
'''OL-HRN-RS-NI8''' - All 
'''OL-HRN-RS-TL5''' - All 
'''OL-HRN-RS-TL6''' - All 
'''OL-HRN-RS-TL7''' - All

Linkr-MBT

2022-08-25T21:28:28Z

70.228.96.105: /* 1.1 - Initial Test Activation */

=1 - MBT Activation & Troubleshooting=
 
==1.1 - Initial Test Activation==
'''1.''' 
:'''a.''' 
'''2.''' 
Notes: If there is only power and ground or the data wires/protocol is not correct the unit will not let new devices pair and give a warning about doors locked. 
[[#top]]

==1.2 - User ==
'''1.''' User search function IS CaSe sensitive. 
'''2.''' 
[[#top]]
==1.3 -
[[#top]]
To be added 
[[#top]]

=2 - MBT Admin=
 
==2.1 - Dashboard==
'''1.''' Displays Stats 
:'''a.''' System totals for each category 
==2.2 - Devices==
'''1.''' Lists all devices registered in the system 
:'''a.''' UUID - Device serial number based off of Bluetooth ID number 
:'''b.''' Owner - Email address of registered owner, if one exists 
:'''c.''' Authorized User - Email address of any used authorized by the owner to use the device 
:'''d.''' Device Status - Shows current status (enabled/Disabled) of device. Gives admin ability to Disable/Transfer/Replace devices 
'''2.''' Click on UUID field to get further details on device status and settings 
:'''a.''' Click any field (BLE Firmware/RS Product/RS Firmware/Owner/Auth User) to go to Firmware/Product/User page 
:'''b.''' Check box to enable/disable AUX functions. You must save after selecting and user MUST back out to home screen for settings to take effect 
:'''c.''' Click Disable/Enable, Save, Transfer, Replace, or Add Auth User to do the listed function. 
:'''d.''' Scroll thru features to see last known RS configuration. (Blue = Default / Red = Current selected option if not Default) 
'''3.''' Click on Owner or Authorized User field to go to user settings (See 2.3 Users) 
'''4.''' Click on Device enabled/disabled button to go to device settings (See 2) 
'''5.''' Click on Disable button to disable device 
'''6.''' Click on Transfer button to transfer the device to another registered user. 
:'''a.''' User must already be registered in the system before transfer is possible. 
'''7.''' Click on Replace button to replace the old device with a different one. 
:'''a.''' Be sure the device you select is not already registered to another user. 

==2.3 - Users==
'''1.''' Email - The email they used to login/register (what else would it be) 
'''2.''' Name - What ever they put for there first and last name when registering 
'''3.''' Role - The functions they are allowed to see or use within the admin and app 
:'''a.''' User - End user who can use the app, that's about it 
:'''b.''' Admin - Omega user who can use the app, and do everything in the website. 
:'''c.''' Technical Staff - Technical user who can use the app, and access to the website for technical troubleshooting and device testing. (can not edit user roles) 
:'''d.''' Manufacturer - Hardware manufacturer with access to Device Labeling only. 
'''4.''' Owned devices - All devices owned by the user 
'''5.''' Authorized devices - All devices this user is authorized to use 
'''6.''' Firmware access - Displays firmware access level of user (see firmware for further info) 
:'''a.''' R - Release - Tested and verified firmware for use by the general public. 
:'''b.''' A - Alpha - Limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for VERY well known users who understand the potential of firmware flaws and will not get there panties in a bunch if the firmware is flawed. 
:'''c.''' B - Beta - More general but still limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for users who may have a particular scenario that needs firmware testing or a custom firmware. 
:'''d.''' I - Internal - Omega and industry ONLY users. 

==2.4 - Brands==
'''1.''' Device Brands - You can only create or delete brands 

==2.5 - Products==
'''1.''' Product creation - You can only create or delete products. 
'''2.''' Information needed to create product. 
:'''a.''' Product Name - Model number. For Omega units use model number on case, for example AL-1670-B would be AL-XX70-B. 
:'''b.''' Product Brand - Must already be existing in the system (see 2.4). 
:'''c.''' Product UUID - Unique HEX value coded in the firmware to ID device. Assigned by Product Dev. 
:'''d.''' Boot UUID (not all products need) - Bootloader UUID needed by some devices. 

==2.6 - Firmware==
'''1.''' View all available firmware. 
'''2.''' Change firmware release stage. 
:'''a.''' Release - Tested and verified firmware for use by the general public. 
:'''b.''' Alpha - Limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for VERY well known users who understand the potential of firmware flaws and will not get there panties in a bunch if the firmware is flawed. 
:'''c.''' Beta - More general but still limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for users who ,ay have a particular scenario that needs firmware testing or a custom firmware. 
:'''d.''' Internal - Omega and industry ONLY users. 

==2.7 - Device Labelling==
'''1.''' Used for production labeling. No support functions here (keep out) 

==2.8 - About==
'''1.''' Website version history. (nothing to see here folks, keep moving) 

=3 - FSF File=
This file defines the firmware banks, features, and options as displayed and used in the app. Banks, Features, and Options MUST match firmware EEPROM map 
==3.1 - Creating FSF file==
'''1.''' 
'''2.''' FSF file notes 
Text in Banks tab under “Bank Read Only Message_EN” column display Error message box with text and will not allow user into bank 
Text in Banks tab under “Bank Warning Message_EN” column display Warning message box with text and will allow user to choose to enter Bank 
Text in Features tab under “Feature Read Only Message_EN” column display Notification message box with text and will not allow user into feature 
Text in Features tab under “Feature Warning Message_EN” column display Warning message box with text and allow user to choose to enter feature 
Text in Features tab under “Help Message_EN” column display “?” icon. When icon selected message box with feature name displays with text in field and user has to choose “ok” to clear 
Text in Options tab under “Option Read Only Message_EN” column display Error message box with text and will not allow user to select that feature 
If no Option Bank-Feature ID number is present for an option “N/A” will display in features list 
Android uses "Yes/No" text, iOS uses "Proceed/Cancel" text when user has a choice to enter or exit option. Be sure message is written so both make sense to the end user.

Linkr-MBT

2022-07-15T16:05:52Z

70.228.96.105: /* 1.2 - User */

=1 - MBT Activation & Troubleshooting=
 
==1.1 - Initial Test Activation==
'''1.''' 
:'''a.''' 
'''2.''' 
[[#top]]
==1.2 - User ==
'''1.''' User search function IS CaSe sensitive. 
'''2.''' 
[[#top]]
==1.3 -
[[#top]]
To be added 
[[#top]]

=2 - MBT Admin=
 
==2.1 - Dashboard==
'''1.''' Displays Stats 
:'''a.''' System totals for each category 
==2.2 - Devices==
'''1.''' Lists all devices registered in the system 
:'''a.''' UUID - Device serial number based off of Bluetooth ID number 
:'''b.''' Owner - Email address of registered owner, if one exists 
:'''c.''' Authorized User - Email address of any used authorized by the owner to use the device 
:'''d.''' Device Status - Shows current status (enabled/Disabled) of device. Gives admin ability to Disable/Transfer/Replace devices 
'''2.''' Click on UUID field to get further details on device status and settings 
:'''a.''' Click any field (BLE Firmware/RS Product/RS Firmware/Owner/Auth User) to go to Firmware/Product/User page 
:'''b.''' Check box to enable/disable AUX functions. You must save after selecting and user MUST back out to home screen for settings to take effect 
:'''c.''' Click Disable/Enable, Save, Transfer, Replace, or Add Auth User to do the listed function. 
:'''d.''' Scroll thru features to see last known RS configuration. (Blue = Default / Red = Current selected option if not Default) 
'''3.''' Click on Owner or Authorized User field to go to user settings (See 2.3 Users) 
'''4.''' Click on Device enabled/disabled button to go to device settings (See 2) 
'''5.''' Click on Disable button to disable device 
'''6.''' Click on Transfer button to transfer the device to another registered user. 
:'''a.''' User must already be registered in the system before transfer is possible. 
'''7.''' Click on Replace button to replace the old device with a different one. 
:'''a.''' Be sure the device you select is not already registered to another user. 

==2.3 - Users==
'''1.''' Email - The email they used to login/register (what else would it be) 
'''2.''' Name - What ever they put for there first and last name when registering 
'''3.''' Role - The functions they are allowed to see or use within the admin and app 
:'''a.''' User - End user who can use the app, that's about it 
:'''b.''' Admin - Omega user who can use the app, and do everything in the website. 
:'''c.''' Technical Staff - Technical user who can use the app, and access to the website for technical troubleshooting and device testing. (can not edit user roles) 
:'''d.''' Manufacturer - Hardware manufacturer with access to Device Labeling only. 
'''4.''' Owned devices - All devices owned by the user 
'''5.''' Authorized devices - All devices this user is authorized to use 
'''6.''' Firmware access - Displays firmware access level of user (see firmware for further info) 
:'''a.''' R - Release - Tested and verified firmware for use by the general public. 
:'''b.''' A - Alpha - Limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for VERY well known users who understand the potential of firmware flaws and will not get there panties in a bunch if the firmware is flawed. 
:'''c.''' B - Beta - More general but still limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for users who may have a particular scenario that needs firmware testing or a custom firmware. 
:'''d.''' I - Internal - Omega and industry ONLY users. 

==2.4 - Brands==
'''1.''' Device Brands - You can only create or delete brands 

==2.5 - Products==
'''1.''' Product creation - You can only create or delete products. 
'''2.''' Information needed to create product. 
:'''a.''' Product Name - Model number. For Omega units use model number on case, for example AL-1670-B would be AL-XX70-B. 
:'''b.''' Product Brand - Must already be existing in the system (see 2.4). 
:'''c.''' Product UUID - Unique HEX value coded in the firmware to ID device. Assigned by Product Dev. 
:'''d.''' Boot UUID (not all products need) - Bootloader UUID needed by some devices. 

==2.6 - Firmware==
'''1.''' View all available firmware. 
'''2.''' Change firmware release stage. 
:'''a.''' Release - Tested and verified firmware for use by the general public. 
:'''b.''' Alpha - Limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for VERY well known users who understand the potential of firmware flaws and will not get there panties in a bunch if the firmware is flawed. 
:'''c.''' Beta - More general but still limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for users who ,ay have a particular scenario that needs firmware testing or a custom firmware. 
:'''d.''' Internal - Omega and industry ONLY users. 

==2.7 - Device Labelling==
'''1.''' Used for production labeling. No support functions here (keep out) 

==2.8 - About==
'''1.''' Website version history. (nothing to see here folks, keep moving) 

=3 - FSF File=
This file defines the firmware banks, features, and options as displayed and used in the app. Banks, Features, and Options MUST match firmware EEPROM map 
==3.1 - Creating FSF file==
'''1.''' 
'''2.''' FSF file notes 
Text in Banks tab under “Bank Read Only Message_EN” column display Error message box with text and will not allow user into bank 
Text in Banks tab under “Bank Warning Message_EN” column display Warning message box with text and will allow user to choose to enter Bank 
Text in Features tab under “Feature Read Only Message_EN” column display Notification message box with text and will not allow user into feature 
Text in Features tab under “Feature Warning Message_EN” column display Warning message box with text and allow user to choose to enter feature 
Text in Features tab under “Help Message_EN” column display “?” icon. When icon selected message box with feature name displays with text in field and user has to choose “ok” to clear 
Text in Options tab under “Option Read Only Message_EN” column display Error message box with text and will not allow user to select that feature 
If no Option Bank-Feature ID number is present for an option “N/A” will display in features list 
Android uses "Yes/No" text, iOS uses "Proceed/Cancel" text when user has a choice to enter or exit option. Be sure message is written so both make sense to the end user.

Linkr-MBT

2022-07-15T16:05:26Z

70.228.96.105: /* 1.2 - User */

=1 - MBT Activation & Troubleshooting=
 
==1.1 - Initial Test Activation==
'''1.''' 
:'''a.''' 
'''2.''' 
[[#top]]
==1.2 - User ==
'''1.USer search function IS CaSe sensitive''' 
'''2.''' 
[[#top]]
==1.3 -
[[#top]]
To be added 
[[#top]]

=2 - MBT Admin=
 
==2.1 - Dashboard==
'''1.''' Displays Stats 
:'''a.''' System totals for each category 
==2.2 - Devices==
'''1.''' Lists all devices registered in the system 
:'''a.''' UUID - Device serial number based off of Bluetooth ID number 
:'''b.''' Owner - Email address of registered owner, if one exists 
:'''c.''' Authorized User - Email address of any used authorized by the owner to use the device 
:'''d.''' Device Status - Shows current status (enabled/Disabled) of device. Gives admin ability to Disable/Transfer/Replace devices 
'''2.''' Click on UUID field to get further details on device status and settings 
:'''a.''' Click any field (BLE Firmware/RS Product/RS Firmware/Owner/Auth User) to go to Firmware/Product/User page 
:'''b.''' Check box to enable/disable AUX functions. You must save after selecting and user MUST back out to home screen for settings to take effect 
:'''c.''' Click Disable/Enable, Save, Transfer, Replace, or Add Auth User to do the listed function. 
:'''d.''' Scroll thru features to see last known RS configuration. (Blue = Default / Red = Current selected option if not Default) 
'''3.''' Click on Owner or Authorized User field to go to user settings (See 2.3 Users) 
'''4.''' Click on Device enabled/disabled button to go to device settings (See 2) 
'''5.''' Click on Disable button to disable device 
'''6.''' Click on Transfer button to transfer the device to another registered user. 
:'''a.''' User must already be registered in the system before transfer is possible. 
'''7.''' Click on Replace button to replace the old device with a different one. 
:'''a.''' Be sure the device you select is not already registered to another user. 

==2.3 - Users==
'''1.''' Email - The email they used to login/register (what else would it be) 
'''2.''' Name - What ever they put for there first and last name when registering 
'''3.''' Role - The functions they are allowed to see or use within the admin and app 
:'''a.''' User - End user who can use the app, that's about it 
:'''b.''' Admin - Omega user who can use the app, and do everything in the website. 
:'''c.''' Technical Staff - Technical user who can use the app, and access to the website for technical troubleshooting and device testing. (can not edit user roles) 
:'''d.''' Manufacturer - Hardware manufacturer with access to Device Labeling only. 
'''4.''' Owned devices - All devices owned by the user 
'''5.''' Authorized devices - All devices this user is authorized to use 
'''6.''' Firmware access - Displays firmware access level of user (see firmware for further info) 
:'''a.''' R - Release - Tested and verified firmware for use by the general public. 
:'''b.''' A - Alpha - Limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for VERY well known users who understand the potential of firmware flaws and will not get there panties in a bunch if the firmware is flawed. 
:'''c.''' B - Beta - More general but still limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for users who may have a particular scenario that needs firmware testing or a custom firmware. 
:'''d.''' I - Internal - Omega and industry ONLY users. 

==2.4 - Brands==
'''1.''' Device Brands - You can only create or delete brands 

==2.5 - Products==
'''1.''' Product creation - You can only create or delete products. 
'''2.''' Information needed to create product. 
:'''a.''' Product Name - Model number. For Omega units use model number on case, for example AL-1670-B would be AL-XX70-B. 
:'''b.''' Product Brand - Must already be existing in the system (see 2.4). 
:'''c.''' Product UUID - Unique HEX value coded in the firmware to ID device. Assigned by Product Dev. 
:'''d.''' Boot UUID (not all products need) - Bootloader UUID needed by some devices. 

==2.6 - Firmware==
'''1.''' View all available firmware. 
'''2.''' Change firmware release stage. 
:'''a.''' Release - Tested and verified firmware for use by the general public. 
:'''b.''' Alpha - Limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for VERY well known users who understand the potential of firmware flaws and will not get there panties in a bunch if the firmware is flawed. 
:'''c.''' Beta - More general but still limited public accessibility intended for testing firmware and report any bugs or issues to the Dev team. Intended for users who ,ay have a particular scenario that needs firmware testing or a custom firmware. 
:'''d.''' Internal - Omega and industry ONLY users. 

==2.7 - Device Labelling==
'''1.''' Used for production labeling. No support functions here (keep out) 

==2.8 - About==
'''1.''' Website version history. (nothing to see here folks, keep moving) 

=3 - FSF File=
This file defines the firmware banks, features, and options as displayed and used in the app. Banks, Features, and Options MUST match firmware EEPROM map 
==3.1 - Creating FSF file==
'''1.''' 
'''2.''' FSF file notes 
Text in Banks tab under “Bank Read Only Message_EN” column display Error message box with text and will not allow user into bank 
Text in Banks tab under “Bank Warning Message_EN” column display Warning message box with text and will allow user to choose to enter Bank 
Text in Features tab under “Feature Read Only Message_EN” column display Notification message box with text and will not allow user into feature 
Text in Features tab under “Feature Warning Message_EN” column display Warning message box with text and allow user to choose to enter feature 
Text in Features tab under “Help Message_EN” column display “?” icon. When icon selected message box with feature name displays with text in field and user has to choose “ok” to clear 
Text in Options tab under “Option Read Only Message_EN” column display Error message box with text and will not allow user to select that feature 
If no Option Bank-Feature ID number is present for an option “N/A” will display in features list 
Android uses "Yes/No" text, iOS uses "Proceed/Cancel" text when user has a choice to enter or exit option. Be sure message is written so both make sense to the end user.