View source for OL-RF-XX-SST

=Overview=
RF antenna using the ADS partner protocol.<br>
'''1.''' Remote programming is '''COMPLETELY''' determined by the Data Start product used. Look at Data Start guide for programming process.<br>
'''2.''' Remote data is shared between the RS module and the antenna so remotes MUST be programmed upon installation.<br>
'''3.''' Remote can NOT be pre-programmed at the time of production. (see note '''1.''')<br>
'''4.''' Some features (Passive Lock, Programmable RS activation, LED flashes, etc..) of the other Omega RF kits are not available.<br>
Button operation is slightly different then other Omega product.<br>
:Signal is transmitted upon button release. The most noticeable difference is RS activation, two quick presses will activate RS. It is recommended that dealer/installer operate the RS a few times before demo to get familiar with the operation.<br>
Firmware update-able via weblink<br>

=Firmware Versions=
Production Version - V1.02<br>
Update Version - V1.03<br>
:Correct data bits to display firmware version correctly.<br>
 
=Possible iData TX Programming=
<u>With ADS hardware</u><br>
Ignition and antenna button(Listed in guide)<br>
'''1.''' Ignition ON press and release antenna button<br>
'''2.''' Hold antenna button<br>
'''3.''' Led in antenna will turn ON<br>
'''4.''' Press lock on each remote to learn<br>
'''5.''' Release antenna button<br>

Ignition 5x:<br>
'''1.''' Ignition OFF-ON  5 times (5th time you need to keep ignition '''ON''', turning OFF the 5th time enters RS valet)<br>
'''2.''' Press lock on each remote to learn (2 sec to press lock between each lock)<br>
'''3.''' Turn OFF ignition<br>
'''Note:''' If done incorrectly the unit could end up in valet mode. You will need to cycle the ignition 5x to get out of valet mode<br>
The RS firmware will go into Valet if no remote is learned no matter how long the key stays on. (tested with MDB-ALL w/RS-FM8)<br>

Ignition and Brake<br>
'''1.''' Ignition ON/OFF/ON, leave in the ON position<br>
'''2.''' Press and release brake 3 times<br>
'''3.''' Press lock on each remote to learn (5 sec to press lock between each lock)<br>
'''4.''' Turn ignition OFF<br>

=Fortin TX Programming=
<u>With EVO-ALL hardware</u><br>
Using FlashLink Manager, be sure “Supported RF kits” is turned ON and set to the proper setting (H3 - CrimeStopper).<br>
'''1.''' Have all transmitters which are to operate the system at hand. With the EVO-ALL data connector (power) disconnected Press & Hold the EVO-ALL programming button. Connect the 4-pin data connector.<br>
'''2.''' Wait for the Blue & Red LED’s to turn on then release the programming button.<br>
'''3.''' Press & Hold the EVO-ALL programming button again, the Blue & Red LED’s will turn off and back on (approx 5 seconds) then release the button. <br>
'''4.''' Turn the ignition ON, the Yellow LED will turn on.<br>
'''5.''' Program the remotes:<br>
• 4-button controllers: Press the LOCK button on the remotes you wish to program one at a time.<br>
• 1-button controllers: Press & hold the START button for 3 seconds on the remotes you wish to program one at a time.<br>
The Blue & Red LED’s will flash off and back on once to confirm each remote is coded.<br>
'''6.''' Turn the ignition OFF and test operation. <br>

<u>With EVO-ONE hardware</u><br>
Using FlashLink Manager, be sure to set Unit Options to the proper setting.<br>
'''1.''' Have all transmitters which are to operate the system at hand. Turn the ignition to the “ON” position then to the “OFF” position.<br>
'''2.''' Turn the ignition back to the “ON” position. The antenna LED will turn “ON”.<br>
'''3.''' Press & release the brake pedal 4 times. The LED will flash rapidly. <br>
'''4.''' Program the remotes:<br>
• 4-button controllers: Press & release the TRUNK button then the LOCK button on the remotes you wish to program one at a time.<br>
• 1-button controllers: Press & hold the START button for 12 seconds on the remotes you wish to program one at a time.<br>
The antenna LED will stop flashing for 2 seconds to confirm each remote is coded.<br>
'''5.''' Turn the ignition OFF and test operation. <br>