80-series

New 80 Series Features

Select inputs/outputs can be configured as status light outputs and override inputs

• When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
• Resistors may be needed for any LED not designed to operate at 12V

Select inputs can be configured as Arm or Disarm inputs
Select inputs can be configured as analog Wait-to-Start
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process
New antennas will work as RF kit for RS-80-G0
70-series remotes and antennas are NOT compatible with 80-series
Remotes now transmit upon button release OR after button is held for 2 seconds
Data protocol and engine detection now set upon key start during vehicle learn

New 80 Series Feature Programming

New Programmable Feature Menus
Features are now broken into 6 Banks

• 1. RS Options
  
• 2. Convenience Options
  
• 3. Security Options
  
• 4. System Behaviors
  
• 5. Output Config
  
• 6. Input Config
  

Feature programming now uses prog button and brake to select banks, feature, and options.

1. Enter programming with Ignition On/Off and prog button 5x
   
   1. System will confirm, with 2 chirps
      
   2. Ignition back On IF brake requires ignition On for operation
      
2. Use prog button to select desired feature bank
   
   1. System will respond with chirps to correspond to selected bank number
      
   2. Chirps will repeat after ~2 seconds delay
      
3. Press brake to confirm selection
   
   1. System will respond with 1x chirp
      
4. Use prog button to select desired feature
   
   1. System will respond with chirps to correspond to selected feature number
      
   2. Chirps will repeat after ~2 seconds delay
      
5. Press brake to confirm selection
   
   1. System will respond with chirps to indicate current option setting of selected feature
      
6. Use prog button to select desired option within feature
   
   1. System will respond with chirps to correspond to selected option
      
7. Press brake to confirm selection
   
   1. System will respond with 1x chirp and return to feature selection in current bank
      
   2. Pressing Brake again will go back to the bank selection option
      
8. Turn Ignition On/Off or wait to exit programming
   

Some Features only have one option by design, mostly for the input/output wires. This will maintain the menu structure if any future options are added to these wires

Feature Reset - Enter programming (ignition on/off, prog button 5x). After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults.

• Once in bank or feature selection holding brake doe 3 seconds will return to Bank selection menu.
  

1514 Reset - Power remote down (Hold "P" & Start). Power remote up by holding "P" and Unlock to clear remote 2-way codes and reset clock and all settings

New 80 Series Hardware

Non-blade control module (AL-80 / RS-80)

• Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
  • Red/White is now Red/Black
    
• Includes single analog sensor port and door triggers in sub harness
  
• New 4-pin harness w/ (+/-)P/L, Ground, and Siren
  
• New 12-pin harness with 22AWG wires for all inputs and low current outputs
  
• New antenna port is now White 4-pin iData style connector on side of module
  
• Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series
  
• Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. Black port will also support Linkr-MBT.
  

Blade control module (AL-80-B / RS-80-B)

• Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
  
  • Red/White is now Red/Black
    
• Includes two analog sensor ports that are now independent zones (?1 - White / 1-Yellow?)
  
• New 4-pin harness w/ (+/-)P/L, Ground, and Siren
  
• New 12-pin harness with 22AWG wires for all inputs and low current outputs
  
• New 6-pin harness with 18AWG wires for Horn/Light flash relays Com/NO/NC wires
  
• New 6-pin harness with 22AWG wires for (-) remote start outputs
  
• New antenna port is now White 4-pin iData style connector on side of module
  
• Door lock port, Green & Black data ports, and Blade connector are all carryover from 70-series
  
• Linkr-MBT can can connect to antenna port and support all functions including antenna as passthrough. This will allow firmware update with no concern about Blade issues. Black port will also support Linkr-MBT.
  

New 80 Series Firmware

V1.0 Initial release 8/5-2025
V1.1 Release 1/5-2026

• Clean up brake input via data to address programming issues.
  
• Add 45 and 60 minute run time.
  
• New runtimes do not allow runtime reset.
  
• Add N/O and Brake Activated Starter Interrupt.
  
• Rearrange Bank 5 feature order.
  
• Add option for Brown siren wire to be Start Interrupt.
  
• Fix Nutek bootloader (MBT firmware update) to prevent unit lockup if BT connection lost during update (must use Weblink to update this on older units)
  

V1.2 Release 5/26-2026

• Initial Release for all Blade compatible units.
  
• Add 15 seconds delay option for ignition override.
  
• Low battery warning on 2-way will follow low volt autostart setting. Set to 11.5 when low volt option set to Off.
  
• Unit will flash parking lights once upon every unlock press when disarmed/unlocked for remote operation visual confirmation.
  
• Lt Green/Black & Lt Green/Red wires can not be programmed for Lock, Unlock, or 2nd Unlock.
  
• 28 seconds option removed from Blue Unlock wire.
  
• Blue/White & Green/Black now have Accessory option.
  

New Remotes

119-03 - One button 1-way in carryover case from 70-seroes

• New xASK logo replaces x433
  
• CR-2032 battery
  

125-03 - Two button 1-way in carryover case from 70-seroes

• New xASK logo replaces x433
  
• CR-2032 battery
  

1419-03 - Four button 1-way with new case design

• xSST logo replaces x433
  
• Green LED next to Start button
  
• Plastic case with metal trim ring
  
• Snap together case, no screws
  
• CR-2032 battery
  

1420-03 - Four button 1-way with new case design

• New xASK logo replaces x433
  
• Blue LED next to Start button
  
• Plastic case with metal trim ring
  
• Snap together case, no screws
  
• CR-2032 battery
  

1423-03 - Four button 1-way in carryover all plastic case from 70-seroes

• New xASK logo replaces x433
  
• Snap together case, no screws
  
• CR-2032 battery
  

1514-03 - Five button 2-way with new case and screen layout

• To turn On - Hold Start for ~5 seconds
  
• To turn Off - Hold "P" & Start for ~5 seconds
  
• New xASK logo replaces x433
  
• USB-C charge port
  
• USB-C firmware update capability
  
  • Hold Trunk while connecting USB connected to Nutek site.(not publicly available)
    

1515-03 - Five button 2-way with new case and screen layout

• 900Mhz xSST logo
  
• To turn On - Hold Start for ~5 seconds
  
• To turn Off - Hold "P" & Start for ~5 seconds
  
• USB-C charge port
  
• USB-C firmware update capability
  
  • Hold Trunk while connecting USB connected to Nutek site. (not publicly available)
    

New Antennas

• REC-1N4A = 1-Way 433Mhz antenna.
  
  • Marked with Omega & xASK logo
    
• REC-2N4A = 2-Way 433Mhz antenna.
  
  • Marked with TILT 3D, ECHO & xASK logo
    
  • Built in tilt sensor
    
• REC-1N9A = 1-Way 900Mhz antenna.
  
  • Marked with Omega & xSST logo
    
• REC-2N9A = 2-Way 900Mhz antenna.
  
  • Marked with TILT 3D, ECHO & xSST logo
    
  • Built in tilt sensor
    

Tilt sensor programming:
-Tilt sensor is Off by deafault
Step 1: Hold the programming button for 5 seconds.
- At 2 seconds, the system will enter valet mode.
- After 5 seconds, the status LED will flash rapidly, release the button. The system will exit valet mode and stay in tilt/feature programming mode.
Step 2: Tap the programming button equal to the desired feature number:
Feature #1: Tilt trigger sensitivity
- The status LED will flash equal to the selection, pause then repeat.
Step 3: Tap the programming button equal to the desiredfeature number:
1 = OFF, 2 = 1 Degrees, 3 = 2 Degrees, 4 = 3 Degrees 5= 4 degrees
- The status LED will flash equal to the selection, pause then repeat.
Step 4: Tap the START button on the remote to confirm.
- The status LED will turn on for 1 second to confirm.
- The status LED will flash to indicate the current feature setting, pause, then repeat.
Step 5: Tap the START button on the remote to confirm.
- The status LED will turn on for 1 second to confirm.
- The module will return to step 02.
TO EXIT: Hold the button for 5 seconds or wait 30 seconds.

REC-2NxA Full Reset:
Step 1: Unplug the harness from the antenna module.
Step 2: Hold the programming button.
Step 3: Plug in the harness to the antenna module.
Step 4: Continue holding the programming button for 5 seconds. Release when the status LED turns on solid for 1 second.
The module is now reset to default feature settings.

Good to know stuff/DEV notes

Antenna LED operation is 100% data driven, some LED sequences like ATV will continue until the count is completed no mater what the ignition status is
Programmable analog LED outputs and antenna LED timing will not be 100% synced.
Hood no longer acts as Door for MT mode, all system have dedicated door trigger
Fortin EVO's are not officially supported, BUT 1-way IVU will program to Fortin. 2-way will not program due to required "enter programming" data message not being sent by EVO at this time