80-series

New 80 Series Features

Select inputs/outputs can be configured as status light outputs and override inputs

• When an alternative override input is used it is only used for Anti Car-Jacking and emergency override, the button on the antenna is still used for programming and other features (pit-stop, low volt/temp AutoStart activation, etc,.)
• Resistors may be needed for any LED not designed to operate at 12V

Select inputs can be configured as Arm or Disarm inputs
Select inputs can be configured as analog Wait-to-Start
Select inputs can be configured as N/C inputs for Hood, Door, or Trunk zones
M/T mode can be programmed to activate when parking brake is set, no need to activate via remote/RS process
New antennas will work as RF kit for RS-80-G0
70-series remotes and antennas are NOT compatible with 80-series
Remotes now transmit upon button release OR after button is held for 2 seconds

New 80 Series Feature Programming

New Programmable Feature Menus
Features are now broken into 6 Banks

• 1. RS Options
  
• 2. Convenience Options
  
• 3. Security Options
  
• 4. System Behaviors
  
• 5. Output Config
  
• 6. Input Config
  

Programming now uses Prog button and Brake to select banks, feature, and options.

1. Enter programming with Ignition On/Off and prog button 5x
   
   1. System will confirm, with 2 chirps
      
   2. Ignition back On IF brake requires ignition On for operation
      
2. Use prog button to select desired feature bank
   
   1. System will respond with chirps to correspond to selected bank number
      
   2. Chirps will repeat after ~2 seconds delay
      
3. Press brake to confirm selection
   
   1. System will respond with 1x chirp
      
4. Use prog button to select desired feature
   
   1. System will respond with chirps to correspond to selected feature number
      
   2. Chirps will repeat after ~2 seconds delay
      
5. Press brake to confirm selection
   
   1. System will respond with chirps to indicate current option setting of selected feature
      
6. Use prog button to select desired option within feature
   
   1. System will respond with chirps to correspond to selected option
      
7. Press brake to confirm selection
   
   1. System will respond with 1x chirp and return to feature selection in current bank
      
   2. Pressing Brake again will go back to the bank selection option
      
8. Turn Ignition On/Off or wait to exit programming
   

Feature Reset - Turn the ignition "on" then "off", immediately press the valet button 5 times. After long siren chirp/horn honk press and hold the Brake Pedal for >2 seconds. The system will chirp once and exit programming with all features set to OEM defaults.

New 80 Series Hardware

Non-blade control module (AL-80 / RS-80)

• Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
  • Red/White is now Red/Black
    
• Includes single analog sensor port and door triggers in sub harness
  
• New 4-pin harness w/ (+/-)P/L, Ground, and Siren
  
• New 12-pin harness with 22AWG wires for all inputs and low current outputs
  
• New antenna port is not 4-pin iData connector on side of module
  
• Door lock port, Green & Black data ports, and Red RS output ports are all carryover from 70-series
  

Blade control Module (AL-80-B / RS-80-B)

• Same 6-pin main harness pinout as 70-seroes with adjusted wire gauges
  
  • Red/White is now Red/Black
    
• Includes two analog sensor ports that are now independent zones (1 - White / 1-Yellow)
  
• New 4-pin harness w/ (+/-)P/L, Ground, and Siren
  
• New 12-pin harness with 22AWG wires for all inputs and low current outputs
  
• New 6-pin harness with 18AWG wires for Horn/Light flash relays input/outputs
  
• New antenna port is not 4-pin iData connector on side of module
  
• Door lock port, Green & Black data ports, Red & Blue RS output ports, and Blade connector are all carryover from 70-series
  

New Remotes

119-03 - One button 1-way in carryover case from 70-seroes

• New xASK logo replaces x433
  
• CR-2032 battery
  

1420-03 - Four button 1-way with new case design

• New xASK logo replaces x433
  
• Plastic case with metal trim ring
  
• Snap together case, no screws
  
• CR-2032 battery
  

1423-03 - Four button 1-way in carryover all plastic case from 70-seroes

• New xASK logo replaces x433
  
• CR-2032 battery
  

1514-03 - Five button 2-way with new case and screen layout

• New xASK logo replaces x433
  
• USB-C charge port
  
• USB-C firmware update capability