CrimeStopper

RSx-G5 Known Issues and Workarounds

During RS if the unit is put into panic mode it will not shut down via brake or timeout.

Workaround - Press unlock twice then press and hold start button till RS shuts down.

RS range less then 10 feet, Lock/Unlock range is normal.

Antenna Firmware - Antennas with date code "2219" were found to have bad/no firmware. Field options are set to 2 pulse for RS or replace antenna with diffent date code. REPL was printed on antennas used to replace antennas for customers. A silver dot was placed on antennas that tested good or had firmware updated.

RSx-G6 Operations

Turbo Timer
Press and hold Brake.
Activate RS (via remote, 3x lock, or data).
System will run for time programmed in Feature #14.
Pit Stop
Use remote as programmed by feature #16 OR press valet twice (same as Excal).
Note: Pit Stop only operates once per key cycle.

RSx-G6

New product based on X70 platform with the same antenna and remote compatibility. Initial release will only be the RS1-G6 (2x One Button remotes) and the RS4-G6 (2x Four Button remotes). Same pin-out as X70 with Crimestopper wire colors (directly compatible with Excalibur T-Harnesses).
Black 6-Pin Main Connector
Pink/White - Ignition (Prog. Feature 2 OR V/L)
Brown - Start
Gray - Accessory (Prog. Feature 2 OR V/L)
Red (2x) - Constant 12V
Pink - Ignition (Prog. via V/L)
White 14-Pin Main Connector
Yellow/Black - (-) Status/GWR (Prog. Feature 10)
White/Black - (-) Light Flash
Brown - (-) Trunk Release (Prog. Feature 20)
Orange/Black - (-) OEM Disarm (Prog. Feature 13)
Gray - (-) Hood Trigger
Red/White - Tach Signal
Pink - (-) Glow Plug(Diesel)/Door Trigger(MT mode)
Green - (-) RS Activation(Automatic)/Parking Brake(MT Mode)
Orange - OEM Arm (Prog. Feature 13)
Black - Chassis Ground
Yellow - (-) Horn Output
Violet - (+) Brake Pedal
White - (+) Light Flash
Red 3-Pin Door Lock Connector
Same as x70
Red 3-Pin RS Harness Connector
Orange/White - (-) Status (Prog. Feature 11)
Red - (+)12V Low Current
Blue/Orange - (-) Start (Prog. Feature 12)

G6 Programming

Vehicle Learn - New for Crimestopper.
1. Turn the ignition "On" (do not start)
2. Press the valet button 8 times in less than 10 seconds - The system will chirp & flash lights to indicate crank delay (Default: 1 chirp/flash = 1.5 seconds).
3. (OPTIONAL) Press valet to change crank delay - Chirp confirmation: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec.
4. Start the engine with the key and let the engine reach a normal idle.
5a. AUTOMATIC TRANSMISSION: Turn the ignition OFF - The system will chirp & flash the lights equal the # of IGN/ACC/START circuits detected (Max: 4).
5b. MANUAL TRANSMISSION: Release the parking brake (this completes ignition sequence learn.) - The system will chirp & flash the lights equal the # of IGN/ACC/START circuits detected (Max: 4). Set the parking brake again.

TIP: If you receive fewer chirps/flashes than circuits you connected, check connections and try again.

Before turning the key OFF, perform the selected MT reservation sequence (feature #6) - When successful, the LED will once every 2 seconds.
6. PUSH-BUTTON-START VEHICLES: Exit the vehicle & take the OEM fob/key 20 ft. away to allow remote start.
7. Activate remote start within 60 seconds of Step 5. Wait until the engine is running and the LED flashes slowly.

- The system will then detect data protocols and the best available engine detection method (datatach, tach, etc.).

- If the brake pedal is pressed before the LED fl ashes slowly, settings are reset and you must repeat vehicle learn.

8. TO SAVE SETTINGS & COMPLETE VEHICLE LEARN: Press the BRAKE pedal (the engine will stop). TO CANCEL/START OVER: Press & release the valet button once.

Remotes - Same as G5
1. Turn the ignition "On".
2. Press valet button 4x - System responds with long siren/horn chirp.
3. Press Lock on 1st remote (Start on 1 button remotes) - System responds with 1 parking light flash.
4. Repeat step 3 for any other remotes - System responds with 2-4 parking light flash for each additional remote.
5. Turn the ignition "Off".

Features - Similar to G5
1. Turn the ignition "On".
2. Press valet button 5x - System responds with long siren/horn chirp.
3. Press valet button equal to feature to be changed - System responds with short siren/horn chirp at EACH button press, once button presses stop the system will confirm feature with chirps.

Long chirp = 10's / Short chirp = 1's Example - 2 Long Chirps and 5 Short Chirps = Feature #25.

4. Press remote button (or brake pedal) to change selected feature - System responds with short siren/horn chirp to confirm option chosen.
5. Repeat 3-4 for additional features that need changed.
6. Turn the ignition "Off".

Feature Reset
1. Enter feature programming (DO NOT SELECT ANY FEATURES).
2a. Press LOCK + UNLOCK (or press BRAKE x 5)
2b. 1-button/2-button models: Press the START button 5 times

- You will get 5 light flashes to indicate reset & exit programming.